HOME |Fused Glass Supplies | Stained Glass Supplies | Precut Glass | Mosaic Glass Supplies |SEARCH |CHECKOUT| Login

Gold Leaves - Fused Glass Jewelry
Fusible Glass Project

(See Glass Tips & Tricks section: How to use Fusible Glass Decals)

· Materials List for COE 90 or COE 96

· Fusible Glass Jewelry Pendant & Earring Set: 1  Inch Long Oval & 1 3/8 Inch Long Black and Clear.

Note: Project can be done Black on Black versus Clear over Black, it will have a deeper color.  Same with white option.

EARRINGS:
COE 90  Item# 27138BK
           and Item# 27138CL 

COE 96  Item# 96138BK
           and Item# 96138CL 

PENDANT:
COE 90  Item# 27126BK
           and Item# 27126CL 

COE 96  Item# 96126BK
           and Item# 96126CL

Fusible Glass Decals: 

Fiber Gold Pack High Low Fire Decal.
            Item# 41126

FUSING SUPPLIES:
Item# 42017 Shelf Paper 1 square foot

JEWELRY FINDING:
Bail for Necklace   Item# 41114
Earring Post  Item# 41118
Earring Reinforce Discs  Item# 41161

Glass Jewelry Supplies:
Item# 41207 Triolyse Glue

· Elmer's™ Glue 
· Rubbing Alcohol, Dish Washing Detergent
· Cloth with very little lint (old T-shirt)
· Cold Polishing - (one of the following)
· Grinder 
· Abrasive Stone 
· Diamond Nail File
· 3M™ Diamond Coated Sanding Sponges

Small Fused Project step-by-step instructions:

Clean Up Supplies:

· Rubbing Alcohol, Dish Washing Detergent
· Cloth with very little lint (old T-shirt)

· Step 1: Remove Glass. To keep from breaking the precut pieces of glass, remove them from the package using an X-acto knife.

· Step 2 - Preparation
· Clean Glass using Alcohol or Dish Washing Detergent. Then dry and set aside on a clean piece of paper or cardboard. 

· Clean & Prep Kiln: 
    · Apply Kiln Wash (Shelf Primer)
    · Cut Shelf Paper to fit shelf
    · Place Kiln Shelf Supports, Shelf and Shelf Paper into Kiln

· Position each piece of glass evenly on top of each other and let sit for a few minutes.

· Step 4: Note:  It is important to note that you need to make sure to touch all glass pieces by the outer edges to avoid finger oil or prints on the surface of the glass from your fingers.

· Step 5:  Place into Kiln Using Fingers around outer edges of the fusible glass project or better yet wear latex gloves, pick up and place the project on the kiln shelf paper/shelf.   Leave a minimum of 1/2" (13 mm) space between each project to ensure they do not touch and fuse together.

· Step 6: Kiln Firing Process- Full Fuse 

Click here for Tips & Tricks for Cone equivalency to Glass Firing temperatures

· Step 8: Prepare Project for Fusible Glass Decals
It is important to follow the instructions that come with your decals! Keeping you glass free of oil from your fingers is important.  Cut the decals leaving a little white edge.  Place in a small amount of clean water and using a pair of tweezers take the decal out of the water when it starts to curl.  Using a tooth pick, hold slide the decal of the paper back and position on the glass where you want it. It is important to remove any air from under the decal.  Some people like to use a squeegee but if you use too much water the decal may slide around (if yes blot with the corner of a paper towel)  You can also use the side of your tooth pick to smooth out the decal.  Let dry completely, over night is preferable, before the final firing. Even the smallest amount of moisture can steam the decal from the glass surface, resulting in a partial transfer.

· Step 9: Firing your Fusible Glass Decals

This project used the GOLD LOW FIRE Glass Decals. Ramp up your kiln slowly while vented, until your reach 1,000 °F, then close your kiln and fire until temperature reaches 1,075 to 1,140 °F.  Ramping slowly is much better than a quick fire to allow plenty of time for burn off and venting.  Then turn off kiln and leave the kiln sit unopened until the next day so your project has had plenty of time to anneal back to room temperature

HOT GLASS TIPS (for Decals): 

- Keep your decals stored in a dry place on their side and not on top of one another.

- Keep your Hi Fire Glass Decals and your Low Fire Glass Decals separately stored, perhaps in well marked envelopes.

- Mark each envelop with the colors/types as well.  Example:  Gold - Low Fire Glass Decals,  Platinum - High Fire Glass Decals, etc.

Attach the metal finding using the Triolyse glue.  Make sure the glass is clean and dry and when placing it on the center, back side.  Maximum strength is reached after 6 hours. (Read the Tips & Tricks for using Triolyse Glue)

Note: The earrings are are using Pierced Earring Reinforce Discs.  Glass earrings can be heavier than most earrings.  A single layer glass will not necessarily require earring reinforce discs but 2 layers would require reinforce discs to keep the hearing laying nicely on the ear and not sagging.

GlassArtPatterns.com, A Sanborn Corporation
PO Box 86747
Madeira Beach, FL 33738

Phone: 727-397-3073 Fax: 866-814-0525

Hours of Operation (USA Eastern Time)

Monday to Friday 9 AM to 5 PM

Features

• Our pre-cut glass is MADE IN THE USA using Glass Made in the USA!
• Fusible Glass Projects: Free with Step by Step instructions.
• Free Fusible Glass Patterns
• Wholesale accounts for Retailers and Class Instructions.
• All of our pre cut glass has smooth edges eliminating the need for grinding and makes for safer handling.
• Create projects faster and more consistently with our quality precut glass.
• We accept Pay Pal & Major Credit Cards
• USPS & UPS are our primary shippers
• Product Search Page.
• Try the "Remember me" option for customer details to prefill checkout form on your next visit.