HOME |Fused Glass Supplies | Stained Glass Supplies | Precut Glass | Mosaic Glass Supplies |SEARCH |CHECKOUT| Login

Glass Dolphin Pin
(Unique Gift)
Fusible Glass Project

(See Glass Tips & Tricks section: How to use Dicro Slide)

Materials List for COE 90 or COE 96

· Note: Project can be done using a variety of Fusible Glass Decals or Dicro Slide ™ 
(but not over one another as they are both metalic based).

Fusible Glass:

COE 90:
· (Clear Base)  1 3/4 Inch x 1 1/3
  Item# 27130CL

· Glass Dolphins Variety Bag
  Item# 41188

COE 96:
· (Clear Base)  1 3/4 Inch x 1 1/3
  Item# 96130CL

Mosaic Glass Category:
· Glass Dolphins Variety Bag
  Item# 41188

Glass Dichroic Category:
  Dicro Slide ™ (Dicro Paper) was used for the curves on the waves on the Clear Back.

· NOTE 2 - Optional Scrap Dichroic small pieces instead of decals could also be used.

Glass Supplies & Tools Category:

· Tie-Tac Back, Clear Vinyl
  Item# 42008

Choose one of the following Tie-Tac backs:

· Tie-Tac Squeeze Back
  Item# 42010

· Tie-Tac Screw Back
  Item# 42009

· Alternate Pin Bar 1 inch Gold Tone
(only recommend when using a white or black base)
  Item# 41163

Item# 41207 Triolyse Glue

FUSING SUPPLIES:
Item# 42017 Shelf Paper 1 square foot

· Elmer's™ Glue 
· Rubbing Alcohol, Dish Washing Detergent
· Cloth with very little lint (old T-shirt)
· Cold Polishing - (one of the following)
· Grinder 
· Abrasive Stone 
· Diamond Nail File
· 3M™ Diamond Coated Sanding Sponges

Small Fused Project step-by-step instructions:

Clean Up Supplies:

· Rubbing Alcohol, Dish Washing Detergent
· Cloth with very little lint (old T-shirt)

· Step 1: Remove Glass. To keep from breaking the precut pieces of glass, remove them from the package using an X-acto knife.

· Step 2 - Preparation
· Clean Glass using Alcohol or Dish Washing Detergent. Then dry and set aside on a clean piece of paper or cardboard. 

· Clean & Prep Kiln: 
    · Apply Kiln Wash (Shelf Primer)
    · Cut Shelf Paper to fit shelf
    · Place Kiln Shelf Supports, Shelf and Shelf Paper into Kiln

It is very important that you pay attention to placement of your Dicro Paper around the edges leaving the center for the placement of the Dolphin as they are larger more 3 dimensional pieces of glass.

· Step 4: Note:  It is important to note that you need to make sure to touch all glass pieces by the outer edges to avoid finger oil or prints on the surface of the glass from your fingers when using decals.

· Step 5:  Place into Kiln Using Fingers around outer edges of the fusible glass project or better yet wear latex gloves, pick up and place the project on the kiln shelf paper/shelf.   Leave a minimum of 1/2" (13 mm) space between each project to ensure they do not touch and fuse together.

· Step 6: Kiln Firing Process- Full Fuse 

Click here for Tips & Tricks for Cone equivalency to Glass Firing temperatures

· Step 7: Firing your Dicro Slide ™  Once place on the glass fire as normal

See-> HOT GLASS TIPS (for Dicro Slide ™): 

· Step 8: Prepare Fused Project
If possible, leave the kiln sit unopened until the next day so your project has had plenty of time to anneal back to room temperature  and it is ready to use. Use abrasives on any rough edges you need to smooth.  If you do find you need to do a lot of abrasive or use a grinder you may need to refire the finished piece to polish the edges. 

· Step 9: Attach Tie-Tac or Pin Back.
It is important to judge the weight of the finished piece.  You may find that you should attach 2 Tie-Tacs so the weight of the glass piece will not pull a hole in the clothing.   Or if using one, you should attach approximately 1/3 rd of the way from the top of the glass pin so it will allow gravity to let the weight of the glass lay flat. 

Alternant choice:

Attach the Metal Pin Bar

Using the Triolyse glue.  Make sure the glass is clean and dry and when placing it on the center, back side.  Maximum strength is reached after 6 hours. (Read the Tips & Tricks for using Triolyse Glue)

GlassArtPatterns.com, A Sanborn Corporation
PO Box 86747
Madeira Beach, FL 33738

Phone: 727-397-3073 Fax: 866-814-0525

Hours of Operation (USA Eastern Time)

Monday to Friday 9 AM to 5 PM

Features

• Our pre-cut glass is MADE IN THE USA using Glass Made in the USA!
• Fusible Glass Projects: Free with Step by Step instructions.
• Free Fusible Glass Patterns
• Wholesale accounts for Retailers and Class Instructions.
• All of our pre cut glass has smooth edges eliminating the need for grinding and makes for safer handling.
• Create projects faster and more consistently with our quality precut glass.
• We accept Pay Pal & Major Credit Cards
• USPS & UPS are our primary shippers
• Product Search Page.
• Try the "Remember me" option for customer details to prefill checkout form on your next visit.