|
Maltese Cross
- Fusible Glass
Materials
List:
· Materials List for COE 90 or COE 96
· Fusible Glass 3 Inch Clear Heart
COE 90 
Item# 27111
COE 96
Item# 96111
· Fusible Glass - 2 Inch Clear Hearts
COE 90
Item# 27110
COE 96
Item# 96110
· Glass Frit, You Pick the Color we suggest red!
COE 90
Glass
Frit
COE 96
Glass
Frit
· Glass Frit & More - Mardi Gras Pack of Mixed - Noodles
& Stringers Red & Black
COE 90
Item# 41069
COE 96
Item# 41066
JEWELRY
FINDING:
Bail
Item#
41114 (Gold) or Item#
41113 (Silver)
FUSING
SUPPLIES:
Item#
42017
Shelf
Paper 1 square foot
Item#
41207
Triolyse
Glue
· Elmer's Glue
· Rubbing Alcohol, Dish Washing Detergent
· Cloth with very little lint (old T-shirt)
· Cold Polishing - (one of the following)
· Grinder
· Abrasive Stone
· Diamond Nail File
· 3M Diamond Coated Sanding Sponges
Small Fused Project step-by-step instructions:
Clean Up Supplies:
· Rubbing Alcohol, Dish Washing Detergent
· Cloth with very little lint (old T-shirt)
· Step 1:
Remove Glass. To keep from breaking the precut
pieces of glass, remove them from the package
using an X-acto knife.
|
|
·
Step 2 - Preparation
· Clean Glass using Alcohol or Dish Washing
Detergent. Then dry and set aside on a clean piece of
paper or cardboard.
· Clean & Prep Kiln:
· Apply Kiln Wash (Shelf Primer)
· Cut Shelf Paper to fit shelf
· Place Kiln Shelf Supports, Shelf
and Shelf Paper into Kiln
·
Break Glass Noodles into small pieces to fit and set aside
|
|
·
Step 3: Put Glass project together
· Use Toothpick or plastic Cocktail fork to put 3
"tiny"
drops of glue and evenly distributed for frit and
noodles to adhere.
· Position Heart in center of 3 inch Clear Heart
· Take a piece of black glass noodle and place a very
small drop of glue on the back side and
position it diagonally across the Red heart to create
the shaft of the arrow.
· Take a piece of red glass noodle and place a very
small drop of glue on the back side and
position it at the far end of the black shaft and on the
surface of the 3 inch clear heart to create the arrow.
· Take the pieces of black and red stringers and place a very
small drop of glue on the back side and
position them at angles at the opposite far end of the
black shaft and on the surface of the 3 inch clear heart
to create the feathers of the shaft.
· Take the "Medium" Red Frit and sprinkle
around the outer edges of the 3" inch clear heart
and try no to get on the Red Heart. Use a Pointed
tip Q-tips
and push the Frit around to be randomly place and not
piles
|
|
|
·
Step 4: Note:
It is important to note that you need to make sure to
touch all glass pieces by the outer edges to avoid
finger oil or prints on the surface of the glass.
·
Step 5 - Place into Kiln Using Fingers around outer edges
of the fusible glass project or better yet wear latex
gloves, pick up and place the project on the kiln shelf
paper/shelf. Leave a minimum of 1/2"
(13 mm) space between each project to ensure they do not
touch and fuse together.
·
Step 6 - Kiln Firing Process- Full Fuse
|
|
SMALL PROJECTS ·
FULL FUSE ·
2 LAYERS |
| Process |
Temp/Min |
Desired Temp |
Soak Temp |
Action |
| Increase/Temp |
30°F/
18°C |
1,000°F /
535°C |
1 Min. |
Remove Vent |
| Increase/Temp |
Full
Speed |
1,400°F /
815°C |
10+ or 10-
Min. |
Observe |
| Flash/Cool |
Highest Speed |
1,100°F /
590°C |
0 Min. |
Open &
Close Lid |
| Hold/Temp |
5°F/
3°C |
955°F / 513°C |
10 min. |
Hold Fire |
| Cool/Temp |
Do
Nothing |
100°F / 38°C |
N/A |
DO NOT LOOK |
Click here for Tips & Tricks for Cone equivalency to Glass Firing temperatures
|
·
Step 7 - Prepare Fused Project
If possible, leave the kiln sit unopened
until the next day so your project has had plenty of
time to anneal back to room temperature and it is
ready to use. Use abrasives on any rough edges you need
to smooth. If you do find you need to do a lot of
abrasive or use a grinder you may need to refire the
finished piece to polish the edges.
|
|
·
Step 8: Finish Project
Clean
glass, dry and select Jewelry Bail color (Gold or
Silver). Apply Triolyse glue to bail and position on
back of glass, centered. It is best to wait 24 hours
for a solid cure and more strength before hanging.
|
GlassArtPatterns.com, A Sanborn Corporation
PO Box 86747
Madeira Beach, FL 33738
Phone: 727-397-3073 Fax: 866-814-0525
Hours of Operation (USA Eastern Time)
Monday to Friday 9 AM to 5 PM
|
|
Features
- Our pre-cut glass is MADE IN THE USA using Glass Made in
the USA!
- Fusible Glass Projects: Free with Step by Step instructions.
- Free Fusible Glass Patterns
- Wholesale accounts for Retailers and Class Instructions.
- All of our pre cut glass has smooth edges eliminating the
need for grinding and makes for safer handling.
- Create projects faster and more consistently with our
quality precut glass.
- We accept Pay Pal & Major Credit Cards
- USPS
& UPS are our primary shippers
- Product Search Page.
- Try the "Remember me" option for customer details to
prefill checkout form on your next visit.
|
»»
Login Status
