HOME |Fused Glass Supplies | Stained Glass Supplies | Precut Glass | Mosaic Glass Supplies |SEARCH |CHECKOUT| Login

Blue Glass Pendant set
Fusible Glass Jewelry Project

(See Glass Tips & Tricks section: How to use Fusible Glass Decals)

Materials List:

· Materials List for COE 90 or COE 96

· Fusible Glass Jewelry Pendant & Earring Set: 

PENDANT & EARRINGS:
COE 90  Item# 27138 Blue (8)
COE 90  Item# 27142 Blue (8)
COE 90  Item# 27126 Blue (2)

COE 96  Item# 96138 Blue (8)
COE 96  Item# 96142 Blue (8)
COE 96  Item# 96126 Blue (2)

DECALS:
            Item# 41214 Fusible Glass Decals Seeds Hi Fire Gold

JEWELRY FINDING:
Pendant Gold Bail - large
  Item# 41114 (1)
Pendant Gold Bail - small
  Item# 41116 (2)
Pendant Gold Bail - small
  Item# 42004 (1)
Earring Stainless Steel Post
  Item# 41118 (2)
Earring Reinforcer Disc
  Item# 41161 (2)

FUSING SUPPLIES:
Item# 42017 Shelf Paper 1 square foot

Item# 41207 Triolyse Glue

· Elmer's™ Glue 
· Rubbing Alcohol, Dish Washing Detergent
· Cloth with very little lint (old T-shirt)
· Cold Polishing - (one of the following)
· Grinder 
· Abrasive Stone 
· Diamond Nail File
· 3M™ Diamond Coated Sanding Sponges

Small Fused Project step-by-step instructions:

Clean Up Supplies:

· Rubbing Alcohol, Dish Washing Detergent
· Cloth with very little lint (old T-shirt)

Step 1:  Preparation
· Clean Glass using Alcohol or Dish Washing Detergent. Then dry and set aside on a clean piece of paper or cardboard. 

· Clean & Prep Kiln: 
    · Apply Kiln Wash (Shelf Primer)
    · Cut Shelf Paper to fit shelf
    · Place Kiln Shelf Supports, Shelf and Shelf Paper into Kiln

Note: Apply Gold Seed High Fire decal to "surface" of the base pieces. 

Capping each decal covered piece with a same sized blue glass piece.

It is important to follow the instructions that come with your decals! Keeping you glass free of oil from your fingers is very important.  Cut the decals leaving a little white edge.  Place in a small amount of clean water and using a pair of tweezers take the decal out of the water when it starts to curl.  Using the side of a tooth pick, hold slide the decal of the paper back and position on the glass where you want it. It is important to remove any air from under the decal.  Some people like to use a squeegee but the side of a tooth pick will also work. If you use too much water the decal may slide around (if this occurs, blot with the corner of a paper towel to wick away the extra moisture). Let dry completely, over night is preferable, before the final firing. Even the smallest amount of moisture can steam the decal from the glass surface, resulting in a partial transfer.

Step 3:  Place into Kiln Using Fingers around outer edges of the fusible glass project or better yet wear latex gloves, pick up and place the project on the kiln shelf paper/shelf.   Leave a minimum of 1/2" (13 mm) space between each project to ensure they do not touch and fuse together.

Step 4: Kiln Firing Process- Full Fuse 

Click here for Tips & Tricks for Cone equivalency to Glass Firing temperatures

Step 7: Adding Bails to all pieces

Attach Earrings Pieces:
Using Triolyse Glue attach an earring post to the top, backside of each earring.

Using Triolyse Glue attach the large gold bail to the top backside of the largest piece.

Using Triolyse Glue attach the smaller gold bails to the top backside of the 2 pieces that are the same size of the earrings.

Cut off 4 of the discs, minus the rings from a gold bracelet. Make sure the loops are positioned at the top and bottom of each of the smaller pieces of glass and using Triolyse Glue attach them centered.

Clean the glass with rubbing alcohol when done.

GlassArtPatterns.com, A Sanborn Corporation
PO Box 86747
Madeira Beach, FL 33738

Phone: 727-397-3073 Fax: 866-814-0525

Hours of Operation (USA Eastern Time)

Monday to Friday 9 AM to 5 PM

Features

• Our pre-cut glass is MADE IN THE USA using Glass Made in the USA!
• Fusible Glass Projects: Free with Step by Step instructions.
• Free Fusible Glass Patterns
• Wholesale accounts for Retailers and Class Instructions.
• All of our pre cut glass has smooth edges eliminating the need for grinding and makes for safer handling.
• Create projects faster and more consistently with our quality precut glass.
• We accept Pay Pal & Major Credit Cards
• USPS & UPS are our primary shippers
• Product Search Page.
• Try the "Remember me" option for customer details to prefill checkout form on your next visit.