HOME |Fused Glass Supplies | Stained Glass Supplies | Precut Glass | Mosaic Glass Supplies |SEARCH |CHECKOUT| Login

Butterfly Heart (3D effect)
Small Pink Heart
Fused Glass Jewelry

(See Glass Tips & Tricks section: How to use Fusible Glass Decals)

Materials List for COE 90 or COE 96

COE 90  Item# 27114 (Pink & Clear)
(Note: COE 90 is a striker color and will fire a darker pink)

COE 96 Item# 96114 (1 Pink & 1 Clear)

Glass Jewelry Finding:
Item# 41116 small Gold Bail

FUSING SUPPLIES:
Item# 41152 Butterflies Gold Low Fire Decal
Item# 42017 Shelf Paper 1 square foot
Item# 41207 Triolyse Glue

· Elmer's™ Glue 
· Rubbing Alcohol, Dish Washing Detergent
· Cloth with very little lint (old T-shirt)
· Cold Polishing - (one of the following)
· Grinder 
· Abrasive Stone 
· Diamond Nail File
· 3M™ Diamond Coated Sanding Sponges

Small Fused Project step-by-step instructions:

Clean Up Supplies:

· Rubbing Alcohol, Dish Washing Detergent
· Cloth with very little lint (old T-shirt)

Step 1: Remove Glass. To keep from breaking the precut pieces of glass, remove them from the package using an X-acto knife.

Step 2 - Preparation
· Clean Glass using Alcohol or Dish Washing Detergent. Then dry and set aside on a clean piece of paper or cardboard. 

· Clean & Prep Kiln: 
    · Apply Kiln Wash (Shelf Primer)
    · Cut Shelf Paper to fit shelf
    · Place Kiln Shelf Supports, Shelf and Shelf Paper into Kiln

Step 3: Adding Low Fire Gold Decal 
It is important to keep your glass free of oil and from your fingers in order to have a clean surface.  We used identical butterflies and placed one on the surface of the clear on the left and the second on the surface of the pink glass on the right both at an angle. 

You can easily add real gold accents to fused glass jewelry or ceramic art using the Ferro Goldrush, gold paint pen. They apply like a felt tip marker and are compatible will any COE glass. To personalize, we wrote the number of the team member on the neck, drew the arrow head design free hand and then out lines it in gold.

Tip: It can be difficult to see the gold being applied.  Test the pen on a piece of white paper to see if is properly distributing and then apply to glass but resist going back over the same area twice as this can make the gold streaky or come out with a more matted brown appearance.

Tip:  Read our Tips and Tricks Instructions for more details on use. It is important to note that when applying to any colored or clear glass, it is difficult to see so you may want to create a paper template and fill in with the pen.  

Fire on top of or between layers to 1050F - 1150F (bonds at 1112 degrees F)

Step 4: Firing your Fusible Glass Decals (and or Ferro Goldrush pen)

This project used the Low FIRE Glass Decals. Ramp up your kiln slowly while vented, until your reach 1,000 °F, then close your kiln and fire according the tac fuse schedule below.  Ramping slowly is much better than a quick fire to allow plenty of time for burn off and venting.  

HOT GLASS TIPS (for Decals): 

- Keep your decals stored in a dry place on their side and not on top of one another.

- Keep your Hi Fire Glass Decals and your Low Fire Glass Decals separately stored, perhaps in well marked envelopes.

- Mark each envelope with the colors/types as well.  Example:  Gold - Low Fire Glass Decals,  Platinum - High Fire Glass Decals, etc.

· Step 5:  Place into Kiln Using Fingers around outer edges of the fusible glass project or better yet wear latex gloves, pick up and place the project on the kiln shelf paper/shelf.   Leave a minimum of 1/2" (13 mm) space between each project to ensure they do not touch and fuse together.

Click here for Tips & Tricks for Cone equivalency to Glass Firing temperatures

Position each piece of glass evenly on top of each other so that you have the butterflies stagger and let sit for a few minutes.  Then place in Kiln for second firing.

Click here for Tips & Tricks for Cone equivalency to Glass Firing temperatures

Step 8: Adding Bail

Clean the glass well. Attach the Bail on the back of the glass using the Triolyse glue.  Make sure the glass is clean and dry and when placing it on the center, back side, and hold in position for 2 minutes.  Maximum strength is reached after 6 hours.

GlassArtPatterns.com, A Sanborn Corporation
PO Box 86747
Madeira Beach, FL 33738

Phone: 727-397-3073 Fax: 866-814-0525

Hours of Operation (USA Eastern Time)

Monday to Friday 9 AM to 5 PM

Features

• Our pre-cut glass is MADE IN THE USA using Glass Made in the USA!
• Fusible Glass Projects: Free with Step by Step instructions.
• Free Fusible Glass Patterns
• Wholesale accounts for Retailers and Class Instructions.
• All of our pre cut glass has smooth edges eliminating the need for grinding and makes for safer handling.
• Create projects faster and more consistently with our quality precut glass.
• We accept Pay Pal & Major Credit Cards
• USPS & UPS are our primary shippers
• Product Search Page.
• Try the "Remember me" option for customer details to prefill checkout form on your next visit.