HOME |Fused Glass Supplies | Stained Glass Supplies | Precut Glass | Mosaic Glass Supplies |SEARCH |CHECKOUT| Login

Fused Glass Picture Frame Ornament
3 1/8 inch Diameter
Fusible Glass Project

Materials List For COE 90 & 96:

COE 90 
Qty 1 Item# 90408 4 inch Clear Circle
Qty 7 Item# 27118 Holly Leaves
Qty 1 Item# 27137 1/2 inch Red Circle
Qty 1 Item# 27142 3/4 inch Red Oval
Qty 1 Item# 41028 White Medium Glass Frit
Qty 1 Item# 41031 Green Fine Glass Frit

COE 96
Qty 1 Item# 96723 4 inch Clear Circle
Qty 7 Item# 96118 Holly Leaves
Qty 1 Item# 96137 1/2 inch Red Circle
Qty 1 Item# 96142 3/4 inch Red Oval
Qty 1 Item# 41043 White Medium Glass Frit
Qty 1 Item# 41045 Green Fine Glass Frit

FUSING SUPPLIES:
Item# 41340 Glastac Adhesive
Item# 41165 E6000 Adhesive
Item# 42017 Shelf Paper 1 square foot

GLASS PICTURE FRAME EASEL BACKS:
Item# 41396 Qty 1 3 1/8 inches Round Open Frame Easel Back
Item# 41317 Qty 1 Glass Hanger Silver Tone

OTHER SUPPLIES:
· Rubbing Alcohol, Dish Washing Detergent
· Cloth with very little lint (old T-shirt)

Small Fused Project step-by-step instructions:

Clean Up Supplies:

· Rubbing Alcohol, Dish Washing Detergent
· Cloth with very little lint (old T-shirt)

Step 1 - Preparation
· Clean Glass:  using Alcohol or Dish Washing Detergent. Then dry and set aside on a clean piece of paper or cardboard. 

· Clean & Prep Kiln: 
    · Apply Kiln Wash (Shelf Primer)
    · Cut Shelf Paper to fit shelf
    · Place Kiln Shelf Supports, Shelf and Shelf Paper into Kiln

Fill between the band with Glastac Adhesive and then sprinkle green glass fine over the adhesive.  Let dry about 10 minutes and then turn upside down, tap backside to remove excess glass fine frit.

Apply Glastac adhesive outside the green band all the way to the outer edge of the glass.  Sprinkle the white medium frit over it, lightly press into place and let dry.  Then turn upside down and tap on back of glass to remove excess white frit.

On the green band of powdered glass frit use Glastac adhesive to hold both of the small ovals in place.  Then proceed to place the green ivy leaves all the way around the green band.  Last, put a drop of Glastac onto the glass where the two red ovals meet and place the round the red 1/2 inch circle on top.

Let glass parts dry for at least 10 minutes until they do not move.

Step 3:  Place into Kiln Using Fingers around outer edges of the fusible glass project or better yet wear latex gloves, pick up and place the project on the kiln shelf paper/shelf.   Leave a minimum of 1/2" (13 mm) space between each project to ensure they do not touch and fuse together.

Step 4: Kiln Firing Process- Tack Fuse 

Click here for Tips & Tricks for Cone equivalency to Glass Firing temperatures

Step 5: Adding Easel Back, Hanger and Photo
Attached the Circle Frame with E-6000 and attach the glass hanger finding to the top backside.  Make sure the glass is clean and dry and when placing it on the center, back side.  Maximum strength is reached after 24 hours.  Use a clamp or clothes pin if you need to hold the hanger in place to keep it centered.

Use the clear insert that comes with the frame and position it over your photo. When happy with the placement, draw around the outer edge of the clear plastic circle, this will provide you a cut line to follow when cutting with your scissors.  Insert the photo into back of the Easel frame and slide latch closed.

GlassArtPatterns.com, A Sanborn Corporation
PO Box 86747
Madeira Beach, FL 33738

Phone: 727-397-3073 Fax: 866-814-0525

Hours of Operation (USA Eastern Time)

onday to Friday 9 AM to 5 PM

Features

• Our pre-cut glass is MADE IN THE USA using Glass Made in the USA!
• Fusible Glass Projects: Free with Step by Step instructions.
• Free Fusible Glass Patterns
• Wholesale accounts for Retailers and Class Instructions.
• All of our pre cut glass has smooth edges eliminating the need for grinding and makes for safer handling.
• Create projects faster and more consistently with our quality precut glass.
• We accept Pay Pal & Major Credit Cards
• USPS & UPS are our primary shippers
• Product Search Page.
• Try the "Remember me" option for customer details to prefill checkout form on your next visit.