|
Doves
in Flight Night Light
Materials List
for COE 90 or COE 96
COE 90
Item#
27152 Clear Precut Night Light Base (Qty
1)
Item#
27135 White Doves (Qty
1 Large & 1 Small)
COE 96
Item#
96152 Clear Precut Night Light Base (Qty
1)
Item# 96135 White Doves (Qty
1 Large & 1 Small)
FUSING
SUPPLIES:
Item#
42017
Shelf
Paper 1 square foot
Item#
41280
Night
Light Mold Set (This project uses the Tall shape)
Item#
41266
Glassline
Dark Blue Fusible Paint
Item#
41263
Glassline
White Fusible Paint
STAINED
GLASS SUPPLIES:
Item#
48005
Night
Light kit
·
Kiln Wash or Hi-fire shelf paper
·
Elmer’s White Glue
·
Rubbing Alcohol, Dish Washing Liquid
·
Cloth with very little lint
SMALL: FREE FUSED GLASS PROJECT
Step-By-Step Instructions & Glass How To information
|
|
Step 1: Preparation - Clean Glass using Alcohol or Dish Washing
Detergent. Then dry and set aside on a clean piece of
paper or cardboard.
Clean & Prep Kiln:
· Apply Kiln Wash (Shelf Primer)
· Cut Shelf Paper to fit shelf
· Place Kiln Shelf Supports, Shelf
and Shelf Paper into Kiln
Prep Mold: Apply a good coat of kiln
wash to the mold, set aside to dry.
|
Step 2: Apply Paint - Drop Blue paint onto surface of clear glass and use a
damp sponge brush use a straight up and down motion, dab
the paint over the entire surface.
Tip: Make sure you sponge is moist so the paint will be
applied as a thin layer, almost like a water color
application. Let dry about 10 minutes.
Lay the
Doves on the glass surface at least an inch from any
edge. Once you are happy with the location you
will then know where you want to apply the white paint
to form clouds.
Drop Whites paint onto surface of glass and use a damp
sponge brush use a straight up and down motion, dab the
paint over the entire surface.
Tip: Make sure you sponge is moist, you want the paint
to be thicker in some areas so let dry and repeat until
you satisfied with the cloud effect. You may find
that you need to clean your sponge brush throughout the
application of the white to avoid any blue mixing to
much with the white. Let dry about 10 minutes. |
|
Step 3: Position Doves - You can place them on the wet paint but should not try
to move them or the paint will come off or you can wait
until you place the Night light painted glass base in
the kiln and the paint is dry to position your doves. |
|
Step 4: Full Fuse - Tip: It is important to note
that you need to make sure to touch all glass pieces by
the outer edges to avoid finger oil or prints on the
surface of the glass.
Place on top of the kiln shelf paper/shelf and full fuse.
|
|
SMALL PROJECTS ·
FULL FUSE ·
2 LAYERS |
| Process |
Temp/Min |
Desired Temp |
Soak Temp |
Action |
| Increase/Temp |
30°F/
18°C |
1,000°F /
535°C |
1 Min. |
Remove Vent |
| Increase/Temp |
Full
Speed |
1,400°F /
815°C |
10+ or 10-
Min. |
Observe |
| Flash/Cool |
Highest Speed |
1,100°F /
590°C |
0 Min. |
Open &
Close Lid |
| Hold/Temp |
5°F/
3°C |
955°F / 513°C |
10 min. |
Hold Fire |
| Cool/Temp |
Do
Nothing |
100°F / 38°C |
N/A |
DO NOT LOOK |
Click here for Tips & Tricks for Cone equivalency to Glass Firing temperatures
|
|
If possible, leave the kiln sit unopened
until the next day so your project has had plenty of
time to anneal back to room temperature.
|
Step 5: Prepare for Slump Process -
Take the kiln shelf out of the kiln. Using the kiln posts, set the kiln washed mold in the middle of the kiln. Place the
prepared fused project on the mold and slump fuse.
|
|
SMALL/MEDIUM PROJECTS
· SLUMP |
| Process |
Temp/Min |
Desired Temp |
Soak Temp |
Action |
| Increase/Temp |
15°F/
7°C |
1,000°F /
538°C |
1 Min. |
Remove Vent |
| Increase/Temp |
Full
Speed |
1,430°F /
777°C |
10+ or 10-
Min. |
Observe |
| Flash/Cool |
Highest Speed |
1,100°F /
593°C |
0 Min. |
Open &
Close Lid |
| Hold/Temp |
5°F/
3°C |
955°F / 513°C |
30 min. |
Hold Fire |
| Decrease/Temp |
3°F/
2°C |
750°F / 400°C |
1 min. |
DO NOT LOOK |
| Cool/Temp |
Do
Nothing |
100°F / 38°C |
N/A |
DO NOT LOOK |
Click here for Tips & Tricks for Cone equivalency to Glass Firing temperatures
Note: If you do not get a full slump, you can
ramp up another 5 degrees (never more than 20 degrees more) and never hold more than 20 minutes
at any temperature.
|
|
Step
6: Adding Night Light Clip
-
If possible, leave the kiln sit unopened until the
next day so your project has had plenty of time to
anneal back to room temperature and it is ready to use.
Use abrasives on any rough edges you need to smooth.
NOTE:
If using a glue on bail to hang the glass, clean
glass and dry.
Attach
the glass
hanger finding to the top backside of the
glass precut using the Triolyse glue. Maximum strength is reached after 6
hours.
(Read
the Tips & Tricks for using Triolyse Glue)
|
GlassArtPatterns.com, A Sanborn Corporation
PO Box 86747
Madeira Beach, FL 33738
Phone: 727-397-3073 Fax: 866-814-0525
Hours of Operation (USA Eastern Time)
Monday to Friday 9 AM to 5 PM
|
|
Features
- Our pre-cut glass is MADE IN THE USA using Glass Made in
the USA!
- Fusible Glass Projects: Free with Step by Step instructions.
- Free Fusible Glass Patterns
- Wholesale accounts for Retailers and Class Instructions.
- All of our pre cut glass has smooth edges eliminating the
need for grinding and makes for safer handling.
- Create projects faster and more consistently with our
quality precut glass.
- We accept Pay Pal & Major Credit Cards
- USPS
& UPS are our primary shippers
- Product Search Page.
- Try the "Remember me" option for customer details to
prefill checkout form on your next visit.
|
»»
Login Status
